Turntable MAT, (11 6/16 diameter) 6 - cut outs in Mat for auto sensing size/arm, position - sensing holes for triangle. Half way - recessed ring in Matte 7/16" wide. Used, good condition, minor scuffs can be cleaned off. #8 condition.
Platter Matte (2 available) 11" Diameter. Cut outs near outer rim for sensing size (9/16"L x 5/16"W). Used, #8 good condition.
platter mat, black 11 3/8" diameter, rubber is good, a few obvious scratches, used, condition #7
Contact us about similar items or replacement parts.
complete w/ wire leads, round motor axl size pulley, tested, oiled, condition # 8+
Pulley for turntable motor 60hz, fits 4mm axel, 3 speed. #9 condition
Contact us about similar items or replacement parts.
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
complete assembly, strobe, window, neon bulb, original neon light, still good, about 1/2 life left, condition # 8
Contact us about similar items or replacement parts.
complete, all parts in tact, springs, etc...entire assembly was removed in tact from unit, condition # 8+ (NOTE: I have encountered 3 variations of this item We need a picture of what your original leaver looked like from the top side view siting position, maybe find a internet photo if necessary that matches yours exactly, so we can provide the correct version.)
Add on wieght for back of tonearm. 1/2" high chrome-look screws into many vintage Turntable, existing counter weights to help to balance arm. #9 condition.
Top section hinge piece on dust cover for allowing bottom hinge knob to fit into . 2 screws, chrome+ (2) pieces. #8+ condition.
tone arm and base, in tact w/ connectors, bearings are good, tone arm rest, cueing mechanism, anti skate mechanism all intact, no counter weight, bad wire, for under arm mechanics, springs, #7 condition
Stylus pressure gauge, 0-5 grams, 1/2 gram intervals. With original box + instruction sheet. New old stock, some water damage to outer carton & label. #9 condition.
We are presently operating on an APPOINTMENT ONLY basis. Please call us first at (617) 926-8020 to schedule an appointment before you come into the shop for repairs, rentals, product recommendations, consultations, or anything other than minor purchases.
33/45, cueing type 5833. Needs MMC5 Stylus. No motor MMX-4HZRPB, No Belt. New high quality phono connectors installed. #8+ condition - Dust cover could be buffed.
SL-1200, SFTG 172-01, original 11.5" full size platter mat, excellent condition, #9
Contact us about similar items or replacement parts.
11.25" full size rubber mat with aluminium 1.5" center, excellent condition, center spindle has small rubber nub that protrudes for 33 spindle only, condition #9+ Note: Check your mat carefully. May also fit CS 510. This hole is for "33" spindle only.
Dust cover scratches very obvious. Unit works. Mechanical internal cosmetics, arm platter excellent. Condition #9.
#40-60, 100-130V 0-14A, 10W motor, good condition, #8
Check us out on facebook.
Thumb screw, #8 condition, slotted/knurled, shaft threaded ⅜" long, fits 1249, 1219, etc., #9 condition
Clear acrylic arm with brush roller, pivot point - not original, suction cup stand, #8 condition
Arm with counter weight pivot + rest, missing roller brush, #8 condition
Customers outside of the US, please note that international shipping can be costly (US Post $16 minimum - up to 8oz or 226g). We are glad to combine orders to reduce shipping costs. Take a look at our shipping policies for more information and estimates of prices and shipping time.
with mat, spring + 45 locking adapter #SFTEC02N01, Note: used with some oxidation on platter, scuff on matte, #8
#SFDPC02N02, tested, known low use, #8+