CD Transport. Goes into an SLP7. Semipro CD assembly. Goes into Semipro consumer machines. Board houses IC's: 1. AN8377N Technics IN. 9, 2. 83745 ID.S. Tested, low use, spindle table rubber slightly aged but acceptable. Condition #9
#SFDPC02N02, tested, known low use, #8+
Direct drive turntable motor in black cup assembly with board, spindle axle, and lead wires.
no spindle, but with magnet rotor plate. Excellent condition.
Equivalent MMN-6C2LKC. With motor board, transformer, and switch. Speed switch. Tested and cleaned. Condition 8+, salvaged from low-use machine.
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
Complete motor and board. Excellent #9 condition, tested and cleaned, low use time.
This is equivalent to: IM-S275-12BUC and M712L-10530V. Syncronis AC 120 volt. 3 Inch square, 1 1/4 high with brass pulley. 4 screw holes to mount into units. #9 condition. Low use.
Micro Controller board. 83962 720 00/273.701 550023.00.000. Has push controls, salvaged from working unit. 9 condition.
Motor and Board PXM-090-D. With PA 2007 and PA 2008, special motor IC. 9/10 condition, completely tested.
Largest version design, smoke "dark". 13 1/2 inches deep, 5 inches high, 19 inches wide. Center point of hinges 12 inch space. 8+/10 condition, minor light hairline scratches, but was buffed. Plastic is still very nice.
Spindle assembly mounted on PCB. Motor #TPM-5A. #9 condition.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
Standard headshell for "vintage turntables", black with silver trim, fingerlift Sony logo, hardware + original box, bayonette, neck nice condition, #9+
4322 010 02043 / 117V 300RPM 60Hz Football shaped mounting plate with 2 holes. With 2 stage pulley that takes square belt. Has finger on pulley to shift belt. Goes into older version Philips - NOT GA 212 or 312 units. Send us a picture of your motor. Condition #9+
used good condition, with IC#8340630 Pulled from turntable w/ broken arm. Condition #9. (2) Available Priced Each
Circuit board, MCB-1 Rev 1, control triac, may need new caps - we can do here, colored wire leads on board, condition #8+
-comes with elevator gear for pitch control
-black and white
-with brass motor pulley
- comes with complete grommet and washer clip kit (QC'd / oiled motor bearings 1.28.21) Condition #9
Older original version pitch control. Retrofit to mount plate, complete assembly on board SFDP112-13. With cable. New.
Customers outside of the US, please note that international shipping can be costly (US Post $16 minimum - up to 8oz or 226g). We are glad to combine orders to reduce shipping costs. Take a look at our shipping policies for more information and estimates of prices and shipping time.
(1) Available. 9V, 12V CW motor. With plastic pulley. Like new. Condition 9.
Complete motor with spring, pitch adjust assembly, pulley, and original wire harness. C-clip mounting; does NOT have original hardware. Salvage from a low use machine. Tested and oiled, with rebuilt pitch adjust mechanism. Condition: 9
(Matsushita) DC3V, tested good, With brass pulley + wiring harness w/plug USED in Model type 5712 5773 Pulled from salvage units. #9 good condition.(2) available, priced each.
mounted in frame [3 3/8" x 2 7/8"] with four mounting stands on top. Excellent condition. Missing the top nut which holds the pitch gear adjuster, but it can easily be taken from your existing motor and put on this one. 9/10 condition. Clean before shipping. Unit has red coverings on coils.
Direct drive motor with board, spindle, and axle gear. Excellent condition, tested.
(2 available), #8 condition, salvaged and tested
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
#1-587-955-1 , transformer #1-446-079-11 IKVY, salvaged from working machine, sensor switch, pitch control, strobe, all intact, #9 condition, salvaged