Pulley for turntable motor 60hz, fits 4mm axel, 3 speed. #9 condition
Contact us about similar items or replacement parts.
complete w/ wire leads, round motor axl size pulley, tested, oiled, condition # 8+
platter mat, black 11 3/8" diameter, rubber is good, a few obvious scratches, used, condition #7
Contact us about similar items or replacement parts.
Platter Matte (2 available) 11" Diameter. Cut outs near outer rim for sensing size (9/16"L x 5/16"W). Used, #8 good condition.
Turntable MAT, (11 6/16 diameter) 6 - cut outs in Mat for auto sensing size/arm, position - sensing holes for triangle. Half way - recessed ring in Matte 7/16" wide. Used, good condition, minor scuffs can be cleaned off. #8 condition.
We leave "SOLD" items on our website for machines that we often repair and provide parts for. This is to give you an idea of the products we typically carry, and direct you to alternatives you may not know about - we often have substitutes for out-of-stock parts, and are happy to recommend workarounds and different solutions to common problems.
(Matsushita) DC3V, tested good, With brass pulley + wiring harness w/plug USED in Model type 5712 5773 Pulled from salvage units. #9 good condition.(2) available, priced each.
8 pin dip IC. Used to control many motors with regulator C1368 on board #6731V. Used, salvaged parts #9
w/ power switch, pitch control + speed reg boards, part # 180 S1 08510010, reg board # 4-2262-18130, pitch control board # 18150A, power switch board # 18160, condition # 9, salvaged from working unit
Add on secondary dynamic weight for tone arm, various versions. Most available are the inch by 1/2" inch. Nickel/chrome wight with arm of others (small/larger). This is a "dynamic" horizontal stabilizer which assists with main weight. #9 condition.
(CAP only - press on) All lettering intact and clear, no wear. Original Technics part. Used, #9 excellent condition.
Headshell, Bayonet style, Used on SL-Bxxx series. With ADC series IV cart mounted on united, no stylus. Used, shows a little wear but Good #8 condition.
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
Black w/finger lift. Used, #9 condition.
Battery powered electronic cleaner. Used in good condition #8
For Turntable motor speed regulator. Tested OK. Salvaged, low use #9 condition.
60hz Pulley for 4 mm shaft 3 speed with grip marks for better traction. #9 condition
with 4mm axle #9 condition low use tested oiled.
12 VDC Motor with brass pulley & regulator IC. #9 condition
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
Which adapts to end of arm at tail, Threaded half inch plug. #9 condition.
Dust cover, with "Dual" logo on center. 14"W x 11.75"D x 2.75"H. Small crack about 1 inch in right rear corner. #8 condition.
W/ Fisher Logo badge in center of top. Size: 15.5"w x 14.5" D x 4.5"H. Note: May fit some "compact" units or console type receivers. No cracks, small scratches. 9- good condition.
Contact us about similar items or replacement parts.
(3) start levers, show picture , possible variations. 8+ used good condition.
Many various levers, start/stop, speed, pitch, 1200 series. Show picture of levers required ($12-$16 each). Used, #8+good condition.
(1) Hinge (1 available) Brown plastic dust cover hinge with tension adjustments screws in rear. Used, #9 excellent condition.
FYI, Around the database you will often see us describe the condition of units on a scale of 1-10. #10 would mean the product is new from one of our suppliers, such as Behringer, Audio Technica, etc. #9 means the product is in perfect condition but is used, #8 implies there are some minor cosmetic scratches but unit is mechanically perfect, and so on and so forth.
1 pair (2) Turntable Feet w/good stems ($38). 1 pair (2) stems only missing feet, ($12). Rubber is in good condition, no cracks. #9 used good condition.
Brass Pulley for Garrard Turntable motor. Includes (2) set screws. Used, #9 good condition.