3.5 gram counterweight for Technics turntable. Half inch wide hole for shaft. Excellent #9 condition with one minor scratch near 0 mark.
Contact us about similar items or replacement parts.
11.5" (diameter) turntable mat for Dual 1219 or 1229. Very good #9 condition with one obvious scratch on inner ring.
Contact us about similar items or replacement parts.
Motor MMN-6P2RB $32 SOLD; control/speed board SFDPB62 $18; controls and switches for speed $14; or all for $50. Very good condition.
Contact us about similar items or replacement parts.
Model unknown, Dust cover has cracked front corner - #5 Condition - (SOLD) Pair of hinges and springs are $16 Hinges supplied with screws and chrome backing plate. Plate measures 1 and 11/16 " wide by 9/16" This plate and hinge screw into cover. Base of hinge fits in slot of turntable base that is 1" wide. #7 condition
Sony turntable motor with wires attached. Includes mounting plate with screws. Excellent #9 condition.
Contact us about similar items or replacement parts.
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
With plastic white pulley, 1 spring. 9/10 condition, guaranteed low time use!
Contact us about similar items or replacement parts.
4 pin Molex to standard USA two blade AC plug.
Contact us about similar items or replacement parts.
Parts machine. Parts can be sold separately. Good #8 dust cover, SOLD ; excellent #9 base, $24; excellent #9 platter, $20. More parts available -( No Belt or stylus) - Call for additional parts.
MMN-5B2R motor with original magnetic pulley. MFG# SFM4BD2N01E New in box. We now have additional motors that can be used as a substitute to this rare motor. Please contact us for addition information.
Contact us about similar items or replacement parts.
Digital pitch control, direct drive. Special headshell with sliding adjuster, 7-13 calibration. Broken actuator arm for auto-return function. Bad cables. Good headshell, feet, and dustcover. Counterweight in #9 condition. Call us for parts
Parts deck. #6 condition dust cover, scratches can probably be buffed out. Hinges, head shell, motor, platter and mat, feet, etc. We have often supplied an alternative fitting counterweight to which will look nice, but is not the original. Counterweights can vary in "weight" so you may be required to add or subtract weight from your headshell or tail end of the arm.
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
Wood base #9 condition $26, Platter mat #8 condition $24, Motor complete with pulley #9 condition $38 (To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque), Aluminum platter, minor stains, corrosion spot #9 condition $10
We have many parts available for the B&O Type 5833 turntable, including dust cover, platter, arm, motor, all in very good or excellent condition. No cartridge or stylus.
We have various automatic record drop spindles available here. Please show us a picture of the spindle you need. We have BSR, Bic, Garrard, Elac, KLH, Dual, etc. $10 to $20 each. *This part has become scarce in working condition; most spindles are missing little rubber record hole grippers. I have plenty of spindles but somehow small little rubber squares must be glued into "umbrella" stem to allow drop functions. Info online does not exist about this fix done by hobbyist but if doing it here, spindles would cost $48 due to fussy labor required to fix, test etc.
Sony PS-X65 turntable for parts or repair. Unit intact, turn on/speed problem. Parts: Headshell #9 $40, Platter #9 $24, Feet #8 $38, Dustcover (SOLD), Tone Arm #9 $48, Dust cover hinges (SOLD)
Speed Lever $16; Speed Chrome Knob $8; Gear Cylinder for pitch belt $8; Complete assembly (rare part) $24.
Contact us about similar items or replacement parts.
#SFDPD2NO1A, Same as many Technics, Spindle cycle gear is cracked, repairable on request, Unit has special AN6639 motor IC, Condition #8 - $28 - Call for availability
We have been selling and repairing professional and consumer audio equipment for over 40 years. (Read some of our customers testimonials here).
We have many parts available, including platter, counterweight, mat, and motor, all in excellent #9 condition.
Contact us about similar items or replacement parts.
Complete parts machine, includes everything but the headshell. Dust cover. All mech. Platter. All in excellent #9 condition. Parts can be sold separately. Contact us for specifics.
Motor complete with spring, pitch adjust assembly, pulley; original wire harness is intact. Screw/nut style mount, with original mounting hardware. Salvage from a low use machine. Oiled and tested, with a rebuilt pitch adjust mechanism. Condition: 9
Contact us about similar items or replacement parts.
Automatic turntable. Complete intact unit, but has problem cycling correctly and consistently. Headshell $24, counterweight $24, platter $24, dust cover #8(with minor faint scuffs) $24, wood base $24, cycling motor $24. Call for parts or complete unit.
Contact us about similar items or replacement parts.
Part #9904 111 31813. Prometec (50hz 250rpm) with small regulator board. Excellent #9 condition.
Contact us about similar items or replacement parts.
Complete Cue mechanism $28 #9 condition - 2 available. TP-16 Arm wand - Arm shows wear with slight scratch on tube.Has repair to left channel cartridge wire. Finger lift is Audio Technica #8- condition $28. Center platter $12 (SOLD); Speed select assembly $18 (SOLD); Pair of hinges $18 (fits wood base only- SOLD); Rosewood base $28(SOLD). Arm pivot assembly Only - 2 available (No arm wand or counter weight) - all wiring good #9 condition $58 or #8 Condition assembly $38. No teardrop knobs available Contact us for other needed parts.
We are a very different kind of shop. To help ensure a smoother experience please read our letter about our current shop policies.
DC 12v. With speed control board. Excellent, tested. This is a commonly requested part used in many turntables, we should have a substitute available. contact us and include your phone number for fastest ordering.
Contact us about similar items or replacement parts.
We have many parts available for Technics SL turntables, including models 1200, 1300, and 1500. SFDP132-02 motor board (SOLD); motor coil board with spindle $28; arm with bad cue mechanism and good bearings $28. All in excellent condition. If possible, please include a picture of the part needed when making parts inquiries.