with special 4-pin connector. This is a non-original power supply custom built to work correctly with smaller Alesis products, but NOT for the Quadraverb. (1000ma)
9vAC, 1-amp power supply for Alesis and other products. Needs connector installed for specific unit use. Supply runs slightly warm, this is normal. Will run most Alesis, Digitech or Art products New. M.I.S
Contact us about similar items or replacement parts.
9vAC 1amp. with 4-pin DIN connector for Alesis products. (New PSU with A.P. wired Connector / NOT for use with Quadraverb.)
9vAC, 1-amp power supply for Alesis Quadraverb and other products. With special 4-pin connector. Supply runs slightly warm, this is normal. New. (part MIS)
FYI, Around the database you will often see us describe the condition of units on a scale of 1-10. #10 would mean the product is new from one of our suppliers, such as Behringer, Audio Technica, etc. #9 means the product is in perfect condition but is used, #8 implies there are some minor cosmetic scratches but unit is mechanically perfect, and so on and so forth.
Original power supply for Alesis product with 4-pin connector. Very good #8 condition with some very minor wear at edges.
Contact us about similar items or replacement parts.
White, 2-hole pin, 11mm spacing. Minor stains, otherwise condition #9
Contact us about similar items or replacement parts.
Nickel-cadmium battery charger for AAA, AA, C, D, and 9-volt batteries. Ten cell locations max. Excellent condition.
New in box. Class 2 power supply, 9vAC, 17w, 1000mA. ART model 6PU410901000WA00.
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
4.5vdc wallwart for Audio Technica products.
Contact us about similar items or replacement parts.
13v DC 300mA output. Excellent condition.
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
4-port, 10 base-T ethernet hub with YP-040 power supply. BNC input connection, standard ethernet RJ45 outputs. Excellent condition.
5vdc, 3amps. Very good #8 condition.
Contact us about similar items or replacement parts.
Mixer board P.S. Input 120 VAC. Output #1 2x17.5 VAC. 2x 650 MA. Output #2 3.0 VAC/ 100 MA. NEW
Contact us about similar items or replacement parts.
internal power supply for UB2442
Contact us about similar items or replacement parts.
PSU-MX2-UL, new in box. Behringer was one of the few that supplied these power adapters, but many other products and companies used this adapter (and did not have replacements) so available inventory was also sold to assist other products when companies could not. At this point the only option we can offer is to wire the supply directly into a mixer. So we would have to have the mixer here. If you want to go that route Please contact me directly at 617-926-8020
Contact us about similar items or replacement parts.
PSU-MX3-UL-01. New in box.
Contact us about similar items or replacement parts.
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
Eurorack power supply. 18V 150mA. #9
Contact us about similar items or replacement parts.
For all MLU mixers. A possible option is to supply a different power supply and adapt a connector correctly for your product. Please send a spec of the part you need, as well as a picture of the connector. It may be possible to adapt another Behringer supply or a substitute part custom made.
Contact us about similar items or replacement parts.