100khz bias oscillator, for use in various Teac cassette and reel to reel decks, used, good condition, condition # 9
Many parts available, Meters, Numeric display, Controls, Knobs etc. #8 condition (No Function Keys- press buttons Play, FF all SOLD) Call directly for price and availability 617-926-8020
with spring and clip. Rubber tire is hard but can be rebuilt/ replaced. used in 480,580 series cassette recorders, used salvaged part. This item needs new rubber... this is a metal arm to plastic platform with all springs and felt. This is the standard design. #7 condition. The rubber tire is required is our listing # 48209
( for Hubs) w/Rubber, (2)- supply + take up arm w/ cups + springs. Salvaged , Used #9 condition.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment. If you have a motor number not listed, show us a nice clear picture and direction of spin. You may also be required to swap your motor pulley. Plastic pulleys slide right off and back on to the new motor. Metal pulleys may require a hot soldering iron on axle to melt glue, then pull off metal pulley and install on axle at same height. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
All springs (2), Hub 4 parts axel. Used, salvaged, #9 condition.
Contact us about similar items or replacement parts.
Take up hub kit complete. 480,580 series. All assembly on axel. #9
w/ Mounting Screws. Salvaged, Used , in good condition, #9
Contact us about similar items or replacement parts.
circuit in a small 1 inch cube, usually 100 KHz, we have many variations available, most new, some use. Also used in TEAC, Dokorder, Pioneer, show picture of yours, maybe we have match, (many oscillators can be used if the "legs fit" they often will operate correctly, although you may require to reset the the record bias.) various numbers on cans are "C2210001", "22132530", "1810110", "NOB008", "13775202", "TEAC52922", "92132522", #8+ condition
1 motor and 3 contact switches, white cam rotator, VA700 BO4 , salvage, tested, #9 condition. 1 available
50K x 2, Part #8075006 (15A 50K Ω x 2) mounted on PCB board #GCMK-77X, #9 condition
Re: International Shipping: We ship internationally often and have yet to encounter a problem or complaint. We are very careful to test the equipment before it’s packed and then to double box the machine with added protection when needed for front panels, etc. We are not amateurs or an ebay store; we know these machines very well and know what it takes to get them to you safely. We use USPS priority internationally which seems to be the cheapest. If you prefer another carrier (you should know who delivers to your area reliably) please let us know. Also please be aware of any tariffs that you may be responsible for upon pick up on your end. International shipping may be expensive but we will make sure it is not a headache on top of the cost. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
2 in stock, special bulbs, bare wire, 1 cm length, approx ~ 3 mm diameter, *See Vinc before shipping*, #9 condition
Swing arm (white) with washers only, for inter idler BX-series, no idler, #9 condition
Contact us about similar items or replacement parts.
Special bulb, T-1 style, bulb with bare wire, 5 volt 115 mA, 6 in stock, *See Vinc before shipping*, #10 condition
3 in stock, felt pads with adhesive back, 7mm diameter, 2.5mm center hole, for idler clutch, #10 condition
This is only ½ of the kit. Contains: hub without strobe, sprocket with arm, small white gear (for intermediate motor), #9 condition
4 in stock, with strobe on back (rear), will fit BX-1, 2, 3, BX 100, 125, 150, 300, #9 condition
All Remotes are now 25% off or Free Shipping!!! (Reel to Reel remotes excluded).
(70VB9429A) cassette motor, test, oiled, #8+ condition
4 track, 4 channel record play head with wire harness for Tascam portastudio, same for use with model 234, 244. Pulled from salvage unit, used good condition #8.
reel hubs, supply and take up, no top caps, with 2 copper tension springs, 4 parts total, very good condition, #8
Complete intact machine. Needs the typically failed cycle mech. Gear to engage play rack ears, knobs. Call for parts broken. #7
Cassette door/window, black, minor surface scuffs, #8+
EG-530AD-9B, 9 VDC motor, from Sony CFD-980 with mounting bracket and wire harness, used - good condition, #8+ condition
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
Power transformer, 120 volt, B-6698, UV2-308, salvage #9
Control board for main drive motor. w/ IC #C1003C2. Salvaged from used machine. #8+ condition.