Turntable MAT, (11 6/16 diameter) 6 - cut outs in Mat for auto sensing size/arm, position - sensing holes for triangle. Half way - recessed ring in Matte 7/16" wide. Used, good condition, minor scuffs can be cleaned off. #8 condition.
Platter Matte (2 available) 11" Diameter. Cut outs near outer rim for sensing size (9/16"L x 5/16"W). Used, #8 good condition.
platter mat, black 11 3/8" diameter, rubber is good, a few obvious scratches, used, condition #7
Contact us about similar items or replacement parts.
complete w/ wire leads, round motor axl size pulley, tested, oiled, condition # 8+
Pulley for turntable motor 60hz, fits 4mm axel, 3 speed. #9 condition
Contact us about similar items or replacement parts.
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
complete assembly, strobe, window, neon bulb, original neon light, still good, about 1/2 life left, condition # 8
Contact us about similar items or replacement parts.
complete, all parts in tact, springs, etc...entire assembly was removed in tact from unit, condition # 8+ (NOTE: I have encountered 3 variations of this item We need a picture of what your original leaver looked like from the top side view siting position, maybe find a internet photo if necessary that matches yours exactly, so we can provide the correct version.)
Add on wieght for back of tonearm. 1/2" high chrome-look screws into many vintage Turntable, existing counter weights to help to balance arm. #9 condition.
Top section hinge piece on dust cover for allowing bottom hinge knob to fit into . 2 screws, chrome+ (2) pieces. #8+ condition.
tone arm and base, in tact w/ connectors, bearings are good, tone arm rest, cueing mechanism, anti skate mechanism all intact, no counter weight, bad wire, for under arm mechanics, springs, #7 condition
Stylus pressure gauge, 0-5 grams, 1/2 gram intervals. With original box + instruction sheet. New old stock, some water damage to outer carton & label. #9 condition.
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
33/45, cueing type 5833. Needs MMC5 Stylus. No motor MMX-4HZRPB, No Belt. New high quality phono connectors installed. #8+ condition - Dust cover could be buffed.
SL-1200, SFTG 172-01, original 11.5" full size platter mat, excellent condition, #9
Contact us about similar items or replacement parts.
11.25" full size rubber mat with aluminium 1.5" center, excellent condition, center spindle has small rubber nub that protrudes for 33 spindle only, condition #9+ Note: Check your mat carefully. May also fit CS 510. This hole is for "33" spindle only.
Dust cover scratches very obvious. Unit works. Mechanical internal cosmetics, arm platter excellent. Condition #9.
#40-60, 100-130V 0-14A, 10W motor, good condition, #8
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
Thumb screw, #8 condition, slotted/knurled, shaft threaded ⅜" long, fits 1249, 1219, etc., #9 condition
Clear acrylic arm with brush roller, pivot point - not original, suction cup stand, #8 condition
Arm with counter weight pivot + rest, missing roller brush, #8 condition
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
with mat, spring + 45 locking adapter #SFTEC02N01, Note: used with some oxidation on platter, scuff on matte, #8
#SFDPC02N02, tested, known low use, #8+