Motor and board. EDS 910 934 5810 001. Has original brass pulley and black plastic gear. Tested, good, low use. 9 condition.
MMI-6S2RWH with transformer, board #OP781T4. 9/10 condition, from a low use machine.
w/ power switch, pitch control + speed reg boards, part # 180 S1 08510010, reg board # 4-2262-18130, pitch control board # 18150A, power switch board # 18160, condition # 9, salvaged from working unit
Speed Shift Lever - 1 unit available Please Read Carefully! This is the rarest demanded lever Total 2 and 1/2 " long - threaded end is 1/4". Lever itself has 2 cuts to allow fit into speed pitch dial. Paddle is 1 and 1/2 inch long and paddle width is 1/2". 1 available with slight wear #8 condition
EG-530SD-3F, 5/12 vDC, 1130/1520/2360/1405 RPM, regulator on board, wire harness w/ switches (bushings+mount screws) , often substitutes for many of these motors, tested condition 9.
OUT OF STATE CUSTOMERS:
Contact us if you are interested in purchasing an item.
We prefer PayPal payments.
We only ship to VERIFIED PayPal Addresses
For customers who do not have a PayPal account we also take Credit Card over the phone.
Please be aware that there is a minimum $4-$6 to ship any part.
Board #PNP-231-A PWM-061-C. Excellent condition, tested.
with screws and adjustment spring, no pulley included. Working motor pulled from new but damaged turntable. Oiled, Tested.
MC-102. 531124. Step transformer in shielded module 2ohm DC input. Probably 20-30ohm cartridge impedance. High impedance out 600ohm DC 20k ohm audio. 1 pin broken but only for mounting purpose on board. #8
SM-100 Complete motor with spring and pitch adjust assembly. Original wire harness is intact; has C-clip style mounts; does NOT have original mounting hardware. Salvage from low use machine, serviced and oiled/tested. Condition: 9
Cable harness. Gold plated. Fits into bottom of arm assembly. #8+ condition.
3vDC motor with wires and pulley. Very good condition.
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
with hinges. Very good #8 condition with some obvious but light scratches, could easily be buffed out with about an hour of labor.
with speed gear, pulley, mounting grommets, and color code leads. Very good #8+ condition.
with spline pulley and drive gear assembly. Excellent condition #9, tested and oiled.
If you want to order a motor from AudioPro, please show us a picture of the motor you need to replace and specify its rotation direction (cw/ccw) when looking down at the pulley.
with board MDC960 and includes IC VC1031. Excellent #9 condition, tested.
with board and spindle. Excellent condition, tested.
with board and connectors, 12-pin Molex. Excellent #9 condition, tested.
We know you have many options for purchasing audio equipment and parts, and we truly appreciate your business. We strive to offer good products at competitive prices. While we can't always match the prices of one isolated reseller, we make up for it by carefully selecting, testing, and finding unique and special rare parts, and we are here for the long run. We guarantee everything we sell and we hope it helps you to enjoy a great listening experience.
tested, low use, excellent condition, will not fit exact version that has 4 gold pins on the board.
For 1019, 1009 and possibly early 1219. Has original wiring harness and plastic connector housing. No pulley, Round black motor housing with three mounting bolts - 4mm shaft. Oiled, light use but good condition. #8+
Motor complete with pulley switch board, speedgear pulley, springs, no belt. Serviced , oiled tested. #9 condition.
Turntable motor. Matsushita MHN-3P2RDB. DC-3V w/ complete wiring harness. Good condition - pulled from unit with broken tone arm. Condition #9
Turntable motor. Matsushita FG Servo. MMX-4H2RPB. 12VDC w/ servo control board. wiring harness. mount hardware (screws + bushings). brass pulley. pulled from working unit. Condition #9
Nice wooden base with clear plastic cover. Square front see thru smoked glass look (like amber) with clear plastic knob for sliding dust cover that gets removed to access playing records, somewhat odd design. Nice walnut veneer. 9/10 condition. (One or two minor scratches, otherwise perfect.) Unfortunately Dual had 8 possible base and dust cover combinations. The easiest thing to do is show us a picture. Sometimes you have to buy complete base and dust cover to make it work.
Local customers, please do not come to the shop without calling ahead first - (617) 926-8020 - for an appointment, so that we can more efficiently help you with your equipment or sound recording needs.
Motor MC924, plastic housing, motor board M30336 and all full length wires/connectors still in place. Tested working. Condition #8+