Cassette tape head demagnetizer. Electronics inside nice cassette housing. Like new condition.
Contact us about similar items or replacement parts.
Transport Motor MMA-6B2LWFC. Head cycling gear cracked. Good for motor, pinch rollers, idler, tape head, gears. No belt. Low use, 90% good head, #9 condition
Contact us about similar items or replacement parts.
Pitch control 3k ohm B $16.Meter ampl PCB-118 $24. Power supply/output amp PCB-143 $36. Teac control (A) PCB 138 and (B) 139 $66. Teac SW PCB-205 (function buttons) $22. Playback ampl PCB-108 connected to record ampl PCB107 with fader, switches, controls, connectors, small chassis plate in tact $48 each. Input ampl PCB-134, includes fader, pots, chassis plate, connectors 52. Front cassette trim with 2 small finish screws $12. Bottom panel $18.
For boards, cosmetic parts. Appears to have bad head amp. Low switch lens. Head, mech all look clean
Tape heads, (Rec/Play 53786008, $48 SOLD more may be available). Erase 53786009 $24. Both heads are complete with wires/connectors still connected. #9 condition.
Check us out on facebook.
Part # RXM-088-A, tested and working, has been oiled, #9 condition.
Contact us about similar items or replacement parts.
Silver face, digital display. Dolby noise reduction, record function. Unit appears to be intact, good heads and pinch rollers. For parts or repair.
For Parts, Call. Machine in excellent condition but both decks no play engage. Excellent face, etc. Good belts, motors. MMI-6H2LWK - $22. Belts - $6. Heads 90%. Need Deck Auto Head Cycle Repair. #8.
Inter idler pulley with rubber #6024067000. #10 condition (new)
Contact us about similar items or replacement parts.
Unit has low use hours, but has defective RF head IC. We can sell whole or break for parts.
Most rubber is aged out, but parts are in good condition for wheels, gears and springs for TEAC 122 and C-3 and many other 1980's cassettes. Send a picture or diagram of the part you are trying to replace. 8/10 condition. $8-$22.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment. If you have a motor number not listed, show us a nice clear picture and direction of spin. You may also be required to swap your motor pulley. Plastic pulleys slide right off and back on to the new motor. Metal pulleys may require a hot soldering iron on axle to melt glue, then pull off metal pulley and install on axle at same height. PLEASE NOTE THAT SHIPPING INTERNATIONALLY WILL BE A MINIMUM OF $16 EVEN FOR SMALL PARTS.
Parts available. Head, #9/10 $18. Pinch roller, #9/10 $16. Back pinch, #9/10 $14. Cover, #8 with obvious dents. Face plate #7/10, Meter $14, switches, IC's, etc available. Call for parts & prices
Same as G2NL0. Counterclockwise direction. New.
Contact us about similar items or replacement parts.
bins oscillator, #NOB-014, excellent #10 condition
Contact us about similar items or replacement parts.
Power supply good. ASIC boards good. Apears to have one side of head IC dead. Unit in near perfect condition otherwise.
(2) Cassette transports with sankyo SHW2L motor $38 each, Value is really for motor. Needs belts, but otherwise intact and functional, belts went soft but cassette deck was seldom operated, very low use time #9 condition.
Unit works but needs new inter-idler. Heads and mechanics have seen low use time, face has finger wear at power, eject, play, stop buttons. Auto head Azimuth system has been disconnected to allow correct head alignment. Unit is serviced, calibrated. For parts or sale as-is.
Contact us about similar items or replacement parts.
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
Fits other models in this series, Wood Case Condition#9 ($24) Top metal cover, $12
#CA80005; probably for most BX series single head designs. Has ear just off pinch roller with 2 holes. New.
Contact us about similar items or replacement parts.
Unit has deep issues and is being sold for parts. Face (top is yellow with age)$24, Transport and belts need to reevaluated- better to see our other complete transport listings , Main board RN-MPM-2742E with high power on switch, which stands 1 inch off board for tape/aux $68, Main board Type A (this version has 5 pin connectors near TAC switch) $38, EQ board RN-MPC2079B $36, Tuner board MPC-1543H $44, Transformer RN-ETP-1003A SOLD. Transformer RN-ETP-1007 SOLD. Everything is in #8 condition unless otherwise specified. IT IS BEST TO SEND US A PICTURE OF YOUR PART SO THAT WE MAY CORRECTLY MATCH IT FOR YOU, THANK YOU.
reel motor, JC-00066, 16VDC with clutch pulley, condition #9
Contact us about similar items or replacement parts.
cassette tape, high bias, 10 pieces in a case, new in box, condition 10, price is for a case
Contact us about similar items or replacement parts.
ADAT Parts machine. Machines appear to have Head IC amp failure. RF head is perfect. Low use otherwise. All other mechanics and electronics are perfect. #8
We keep our database up to date with almost 10,000 items in stock. If you see a part number and a price, we have that item in stock.
Transformer #NTK94243 and # PN-ETP1003A. #9 condition.
Contact us about similar items or replacement parts.
(Motor 70001200 with pulley SOLD- others available see our listing 58677.) Inter Idler /no spring $22, Digital counter and board HD38701A08 SOLD (others are available, check our web search). Main circuit board 52101948-02 $28. Pitch control with board 52101959 SOLD. Function button board 52101210-01 $12. 9/10 condition.