can go either CW or CCW depending on polarity of voltage, with brass pulley, tested and lubricated, salvaged #8 condition.
Black metal, 5/8" hole to hole mount, excellent condition pair.
many other models, cycle cams and center spindle, show picture of required part, most parts.
with metal pulley, excellent condition.
Contact us about similar items or replacement parts.
yellow, black, and white parts with spring. Excellent condition, two pieces available.
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
From GA 212 with large brass pulley 1 1/8" diameter, 1/19" width. Includes mounting bracket and lead wires. Very good condition, cleaned and tested.
Contact us about similar items or replacement parts.
complete board with all parts intact. Excellent condition, salvaged from good machine.
with spline pulley and drive gear assembly. Excellent condition #9, tested and oiled.
If you want to order a motor from AudioPro, please show us a picture of the motor you need to replace and specify its rotation direction (cw/ccw) when looking down at the pulley.
9v DC motor, CCW rotation direction, with wire leads, board, and brass pulley. Matsushita MMI-6S9RWH. Excellent condition, tested good.
This is a scarce, hard to find motor !!! We are currently out of stock. If possible, please send us a picture of the motor you want to replace when you make your request. Substitute motors, when available, will cost about $36. USD plus $8 shipping in USA. (about $16 shipped overseas)
Contact us about similar items or replacement parts.
no spindle, but with magnet rotor plate. Excellent condition.
To inquire about a motor you can show us a picture and/or find model number on your motor. Actually some model numbers are virtually the same except slight cosmetic (color) or historical change, or a top bracket mount is slightly different. Once the actual look is the same then it is the same motor. It is true that sometimes the motor rotor develops cracks and can have weak torque.
Direct drive motor with board, spindle, and axle gear. Excellent condition, tested.
Cosmetic trim and external parts for various models in the 500 series. Please show us a picture when requesting a specific part.
with board MDC960 and includes IC VC1031. Excellent #9 condition, tested.
with board and spindle. Excellent condition, tested.
with board and connectors, 12-pin Molex. Excellent #9 condition, tested.
red arm about 2.5" long with black lever and spring. Excellent condition.
All motors are tested for torque and oiled where required. We have prepared years ago to find and salvage parts to help repair nice older equipment.
(2 available), #8 condition, salvaged and tested
T.T. motor, board marked JVC S73HB, motor MC932C17222, coils tested, #9 condition
Contact us about similar items or replacement parts.
Direct drive turntable motor in black cup assembly with board, spindle axle, and lead wires.
#1-587-955-1 , transformer #1-446-079-11 IKVY, salvaged from working machine, sensor switch, pitch control, strobe, all intact, #9 condition, salvaged
Levers, frames, covers, springs, show picture of part required, most parts ($8) plus shipping - Out of stock of 1229 speed lever ***Send picture of top shaft and lever to help us find correct part as several variations exist ***
Please be aware there is a minimum $4-$6 to ship any part. International orders will be $14-$16 to ship for anything larger than an envelope. Shipping costs are non negotiable, so please, PLEASE do not ask for a part, or for us to search for, or quantify a part if you cannot pay for the shipping.
Possibly for Sansui or Kenwood, heavy duty hinges. Very good condition with some rust. Please show a picture of your parts when requesting hinges.